EPS to STL
Free online EPS to STL converter. Convert EPS to STL and get a 3D-printable STL with real thickness, ready for Cura, PrusaSlicer and Bambu Studio. Reads EPS vectors without Illustrator or Ghostscript. Runs in your browser: nothing uploaded, no sign-up.
Works with: LightBurn · Fusion 360 · AutoCAD · GRBL · Mach3
Drop several files at once to convert the whole folder in one pass. Got a different format? A PNG, JPG, HEIC, PDF, SVG or DXF still comes out as STL.
× removes a colour and its shapes; click a swatch to change it. Every format follows.
- Runs in this tab
- No sign-up
- Full resolution out
Batch
Every file is traced on its own at its own resolution, with the settings in the panel. A file converted here comes out identical to the same file converted by itself.
Every format
Conversion settings
Machine output
Height follows the source aspect ratio.
Laser and Router follow the traced outlines. Engrave photo burns the picture itself, line by line, for photos and portraits.
Heat transfer vinyl is pressed face down, so it has to be cut mirrored. The second box is the overcut in millimetres: a drag knife starts each shape pointing the wrong way, and running past the start covers that stretch properly so the piece weeds out clean.
Beam or bit width. Left at zero the tool runs down the centre of the line, so a part finishes one tool width undersize. Set it and the path is offset by half, with holes offset the opposite way.
Holes before the part that holds them, so nothing comes loose while there is still cutting to do. Also shortens the travel between cuts.
See it on your product
Put this artwork on a 3D mug, tumbler, sign, phone case or canvas, turn it all the way round, or drop it onto a photograph of your own blank. The preview page has the product picker, the colours and the placement controls.
Open the preview and renderHow it works
Upload your artwork
Mono mode is preset, a single cut outline is what a machine wants, not colour layers.
Set your real size
Choose millimetres or inches and the finished width. The file carries physical units, not pixels.
Check the preview, then cut
Inspect the toolpath before you download. Cuts draw solid, rapids dashed.
EPS to STL online, free
EPS to STL online: the closed shapes of the EPS are extruded to a solid at the height you choose, ready for Cura or PrusaSlicer. EPS to STL free and an EPS to STL converter online: nothing to install.
Other shapes to solids: SVG to STL, PNG to STL. For flat vectors: EPS to SVG, EPS to AI. EPS to OBJ: open the STL in Blender and export OBJ.
Why it matters
Correct units, stated in the file
DXF exports write $INSUNITS. Without it a part imports at 25.4x the intended size, which is the single most common cause of a ruined first cut.
Y axis the right way up
SVG puts +Y down the screen; CAD and CAM put it up. We flip it. Exporting without that correction gives a part mirrored about the X axis, it cuts, but backwards.
Closed contours
A cutter following an open outline leaves the part attached. Outlines are closed, and anything that is not is flagged before you download.
Conservative G-code
The tool is disengaged before every reposition, retracted before every rapid, and the program always ends tool-off and clear.
Is EPS to STL worth paying for?
A STL is the file a shop actually runs. Walk through the artwork requirements a laser cutter, a CNC shop or a sign maker publishes and the same request appears: send something a machine can follow. What turns up instead is a screenshot or a logo pulled off a website at 600 pixels, and somebody redraws it by hand — twenty-five to forty minutes — or sends it to an art service at $25 to $60 a file.
The conversion here is free and unlimited and stays that way. The paid plan is what unlocks the machine formats, which are never watermarked at any tier because a mark in a cut file is extra cut paths a machine would run.
Questions
What units does the file use?
Whichever you pick, millimetres or inches, and the choice is written into the file header so the receiving software does not have to guess.
Will this work with my laser?
DXF is written as R2000 by default, which LightBurn, Fusion, AutoCAD and current CAM packages all read. There is an R12 option for older controllers that predate LWPOLYLINE.
Can I trust the G-code?
Preview the toolpath first, and dry-run any new program above the material. The generated code assumes you have set your own work origin, and it homes nothing.
Reading on STL and machine files
EPS to STL: here, by hand, or on a server
| Veconvert | Illustrator, by hand | A paid vectorizer | |
|---|---|---|---|
| What it costs | Free preview; one file for $3.49 as a guest ($3.99 for technical files), $6.50 in bulk | $23 a month | $8–15 a month |
| How long it takes | Seconds | 30–60 minutes by hand | Seconds |
| Skill needed | None. Drop the file | You have to be able to draw | None |
| Where your file goes | Nowhere. It stays in this tab | Stays on your machine | Uploaded to a server |
| STL with real units | Yes | Yes, with setup | Usually pixels |
| Machine files too | DXF, G-code, PLT, STL from the same trace | Separate export each time | Rarely |
More converters and tools
Ready to convert your EPS?
Free, unlimited, no account, and nothing leaves this tab.
Convert a EPS now